Step 3 - Winterize

Step 4 - Winterize

Introduction

Winterization is a step to remove plant waxes from the crude oil. The petroleum industry has been dealing with this since the early days of gushers. The cooking oil industry as recently as the 1950s. The implementation in the cannabis industry was popularized by Gray Wolf with his published QWET and QWISO procedures. The theory being plant waxes crystallize at cold temperatures into a visible mass that can then be removed through gravity, vacuum or centrifugal force filtering. The cooking oil industry performs winterization as one of the refinement steps, but interesting enough, this is done later in the refinement pipeline rather than as a first step.

For cannabis products, winterization is normally done with extraction by using sub-zero temperature alcohol. Historically, this has taken 24-48 hours to freeze the plant and large volume of alcohol, wash the plant then filter it. Again, all this cooling takes quite a bit of time with the volume of alcohol and must be done in the freezer. Typical extractions use quarts, up to gallons of alcohol which must be kept near frozen through out the entire extraction process.

Then in the summer of 2021, through a simple test, it was found the waxes are in fact very hardy, surviving a hot distillation. This means winterization can be performed later on which led to the discovering of Rapid Winterization.

In the past, winterization has been performed on large volumes of alcohol. What happens when its just a cup of Ethanol? Freeze time scales in a favorable direction. This small amount of alcohol needs very little time to reach -20c/-0f, the coldest temp in your freezer. If you have some dry ice, you can speed up the freeze even more by creating an alcohol/dry ice bath and set the bowl in that. The dry ice bath can easy fall below -40c/-40f so be careful and always wear protective gear. Boiling action of the bath starts fast, but slows as the alcohol reaches it's coldest temperature. 

There is another benefit of having winterization follow Distillation. By first distilling in water, virtually all the polar and most semi-polar compounds are removed from the oil, leaving a majority of non-polar lipids, IE, fats, waxes and oils as a dark resin. High proof ethanol is used for dissolving this sticky resin. Lower proof Ethanol can be used, but has higher water content making it harder to dissolve the resin, therefore, you need 2-3 times the amount. This is useful for patients without access to 95% alcohol. More on this later in Tips and Tools.

Again, here is the power of polarity. Water is the most polar solvent on the planet, the polar opposite of the non-polar cannabis resin. By mixing the two, you may see the resins actually pooling and flowing like wine veins on the sides of a wine goblet before solidifying into waxes. This is polar forces at work causing separation between the dissolved oils and water as the solution cools. Freezing this amount of fluid takes very little time. Waxes crystallize faster in this small volume of alcohol. 

After the waxes have been collected in the paper napkin, save the napkin to harvest the waxes for other uses. Your dissolved oils are now ready for final reduction.

Procedure Summary RxCE Rapid Winterization

From the prior step, you should have a small bowl of dissolved oils in alcohol and a small jar with about an ounce of alcohol.

1. Place the bowl and jar of alcohol into the freezer for 1 hour to crystallize the waxes. 

2. Set a cone coffee filter or folded paper napkin in a funnel, in a small capture jar, in the freezer. Dribble a few drops of 90+% in the filter to pre-wet it.

3. After an hour, Pour the bowl of waxy oils through the paper filter and let it drain until the waxes crack, meaning you will eventually see the waxes looking dried out and broken apart. You can optimize this by wringing out the coffee filter to remove the fluid leaving the waxes behind, but heads-up, handling it may cause some waxes to melt.

4. Once the alcohol drains leaving waxes behind, use the additional chilled alcohol to clean out the bowl, then pour over the waxes and stir it up. Put this back in the freezer and let it drain. This additional bit of alcohol leaches out any free oil. The wax will become lighter in color as the alcohol drains away.

References:

For further reading on waxes, please visit Gray Wolf’s post on Plant Waxes.

For further reading on winterization, please visit Gray Wolf’s post on Winterization.

For further reading on ethanol winterization, please visit Gray Wolf's post on QWET.

For further reading on isopropyl winterization, please visit Gray Wolf's post on QWISO.

Fun Discussion:

Here's Fun Science: A history question to ChatGPT on when dewaxing became a thing -

Q: About what year did the cooking oil industry implement dewaxing as part of the cooking oil refinement process? 

A: The implementation of dewaxing as part of the cooking oil refinement process in the cooking oil industry began in the mid-20th century. The exact year can vary depending on the specific region and company, as different companies may have adopted the process at different times. However, dewaxing as a refining step to remove waxes from cooking oil started gaining prominence in the 1950s and 1960s.

Dewaxing is a process that involves chilling the oil to low temperatures, allowing waxes to solidify and separate from the oil. This step is particularly important for oils that tend to solidify or cloud at lower temperatures, such as some vegetable oils like sunflower oil or corn oil. By removing waxes, the oil's clarity, stability, and functionality are improved, making it more suitable for various cooking and food preparation applications.

Since its introduction, dewaxing has become a standard practice in the cooking oil industry to enhance the quality and usability of vegetable oils, ensuring they remain liquid and clear even at lower temperatures.

Tips and Tools

Tip: Take a look at the color of the waxes above from a Rapid Winterization. The left picture is darker showing chlorophyll that bonded over time. Pour in additional chilled alcohol and stir up the waxes. This will leach out any remaining oil.

Tip: If you have access to Dry Ice, you can accelerate this freezing process. Be careful! Always wear protective gear when using dry ice. Place your Dry Ice in a larger metal pot and add at least 91% Isopropyl. After a couple minutes, the boiling will slow as the alcohol reaches it's coldest temperature. Now, float your bowl of dissolved oils in the second bowl. The dissolved oils will quickly reach a low of -40c/-40f.  

Tip: Save the waxes in a closed container in the freezer for later use to make topicals, etc.

Troubleshooting

Disclaimer:  Your use of any information or materials on the C.H.S. Website is entirely at your own risk, for which we shall not be held liable. It shall be your own responsibility to ensure safe use and operation of any processes, products, services or information made available through C.H.S publications and Website.